旼컴컴왯컴왯커旼컴� 旼컴� Christmas 1995 � 캑� 잎 납 읏� 읏 � 粕� 납 납 � 쳐컴컨올컴컴캑쳐컴캑쳐컴캑 � 캑� 납 . 납 . � 쳐 냅� 粕� 납 粕 읕컴컴� 읕컴� 읕컴켸읕컴� Presents..... � � 靈커 靈커 � � 켠� 靈커 靈커 靈켠컴� 靈커 靈커 靈커 爐커 靈커 � � � � 픔캑 � 픔좆 � � � � 커 � � � � � � � 픔캑 픔쬔 � 픔캑 픔컴컴� � � 聃켸 � � 켕� � � 聃켸 � � � 聃켸 � � � � � � 聃켸 � � � � � � � � � � � � OK dudes.... the following text is an extract from the engineers guide for British Telecom Monarch switchboards. Now these have been around for a few years but are still very common in lots and lots of companies. You wanna take call barring off your extension? You wanna take your extension off of logging altogether? Now you can dial who you like, where you like, when you like without the nasty analysis cathing you out. But, hey, use your fucking loaf m8.... if your gonna take barring / logging off do a few others around you so it looks like an accident or something, and watch out for bill itemisation that may show your USA BBS call despite taking logging off ;) Why not pretend you lost someones number and ask if they can check the logs to get it back? That will give you a good idea of how it all fits together. MMI is found on the operators console.... A master phone is often found on top of the Monarch kit in the PABX room itself, Take It Easy.... fuLLstop 갚꾼껑� 갚꾼껑� 갚꾼껑� 갚꾼껑� 갚꾼껑� 갚꾼껑� 갚꾼껑� 갚꾼껑� 갚꾼껑� 갚꾼껑� Monarch MMI (man Machine Interface) Symbols # = Hash (just in case it gets corrupted) EXT = Extension MMI LEVEL SYSTEM LOCK CODE PASSCODE NUMERIC CUSTOMER *100* 142 MAINTENANCE *200* 9999 SPECIALIST *300* 2783 [use with caution] From console or master phone Enter *MMI_level*PASSCODE# e.g. *100*142# *200*9999# *300*2783# NB pascode isn't echoed, instead stars are displayed '****' From console you may press MMI key then PASSCODE# If you have correct passcode you will get MMI READY or MMI rejected if wrong. If using Masterphone press Recall to enter command mode. General 1. After entering a command press escape from console to return to MMI input or press recall from masterphone. 2. Use stepon key to continue display 3. Masterphone when in MMI mode you will get a 1.4Khz tone, errors give NU tone. Create Masterphone *113*EXT*1*1# Remove Masterphone *113*EXT*1*0# Listing outgoing route codes *174*CAT# Set time/date *555*HRS*MIN# *666*DAY*MON*YR# | Year is last two digits only Activate Extension *114*EXT# De-activate Extension #114*EXT# Change Extension *150*1st (old)*2nd (new)# Metering reset meter for one extension #140*EXT# reset all #140# to list *140*EXT# Call Logging Cancel Logging #270# Start logging *270# Call Barring Set Barring *170*EXT*CATno# Cancel Barring #170*EXT*CATno# Cancel all barring #170*EXT# CATnos Calltypes possibly 1 ?? 9 2 ?? 90 3 9089 4 90860 5 etc 6 7 8 Different for each installation Special facilities *111*EXT*code# Cancel #111*EXT*code# Code Facility 9 Dial 9 block exemption 40 Divert barred 44 Divert to OP 51 Bar incomming calls 56 Exclude from wait on busy 57 Exclusion from intrusion (OP can usually overide) 75 Recorded announcment Cancel dial 9 block #9# List system short codes *173*Number# number=0-19 if blank all listed Store short code *101*value*number# value=00-39 NB number can only be 11 digits when entered from masterphone, best use just 9 Personal abbreviated dialling Change MMI code *199*KEY# where KEY is customer code Check code *198# MISC commands Cancel alarms #203# Cancel MMI counters #301# Clear fault record #201# Virgin cold start *260*99# DON'T USE These Delete port *260*PORT# Execute warm start *352#