Protocol: Xxctuc2ds  Sequence: xxctuc2ds.c  Apptype: solidseq1d

Description: Constant time uniform crosspeak COSY. 

Parameter Groups: 

90H:  Module:  no
Sequence:  tancpx.c  
Description:  Provides a 90-degree pulse on dec that can be used 
              as a preparation pulse. Also used to store the dec 
              calibration.
Parameters:  Channels Page
       aH90  - the amplitude of the pulse.
       pwH90 - the pulse length.

cpHX:  Module:  yes
Sequence:  tancpx.c
Description:  Implements constant, linear or tangent-ramped cross 
              polarization from dec to obs. 
Parameters:  Sequence Page
       shHX - 'c', constant, 'l', linear and 't', tangent shape on
               the channel designated with chHX. 
       chHX - the variable-amplitude channel, 'fr' from or 'to', to. 
       aHhx - median amplitude of the dec channel.
       aXhx - median amplitude of the obs channel.
       bHX -  +/- tangent curvature (>0 to 1.0e5).  
       dHX -  amplitude width of the ramp. A negative width sets a
              ramp that starts high and decreases in amplitude.
       tHX -  contact time
       ofHX - overall offset on the variable channel
       frHX = 'dec' -  channel with the initial polarization (must 
              be set - not shown).           
       toHX = 'obs' -  channel with the final polarization (must be
              set - not shown). 
Implementation:  CP hx = getcp("HX",0.0,0.0,0,1); 
Underscore functions: _cp_(hx, phHhx, phXhx);  
 
spnlH:  Module:  yes
Sequence:  tancpxs.c
Description:  Implements TPPM, SPINAL16 SPINAL32 and SPINAL64 as a
              MPSEQ. Used as an alternate to the DSEQ router.
Parameters:  Sequence Page
       aHspnl - amplitude of SPINAL or TPPM.
       pwHspnl - approximate 180-degree flip on dec.
       nHspnl - 2 for TPPM, 16, 32, 64 for SPINAL.
       qHspnl - Number of PULSES (not cycles!) in the .DEC file.
       ph1Hspnl - TPPM +/- phase, "phi".
       ph2Hspnl - additional SPINAL phase, "alfa".
       ofHspnl - overall frequency offset.

The Basic SPINAL cycle Q is: [(phi),(-phi)],(phi+alfa),(-phi-alfa),(phi+2alpha),
                             (-phi-2alpha),(phi+alfa),(-phi-alpha). Note that
                             the first two elements [(phi),(-phi)] are TPPM.
SPINAL repeats with: [[Q-Q]-QQ]-QQQ-Q]. where the [] include 16,32 and 64 pulses.
                     The "Supercycle" of this SPINAL is one PULSE, (not Q).
Implementation: MPSEQ spnl = getspnl("spnlH",0,0.0,0.0,0,1);
Underscore functions: _MPSEQ functions.

spnlmH:  Module:  yes
Sequence:  tancpxs.c
Description:  Implements TPPM, SPINAL16 SPINAL32 and SPINAL64 as a
              MPSEQ. Typically used for Mixing or F1 periods. 
              Used as an alternative to the DSEQ router.
Parameters:  Sequence Page
       aHspnlm - amplitude of SPINAL or TPPM.
       pwHspnlm - approximate 180-degree flip on dec.
       nHspnlm - 2 for TPPM, 16, 32, 64 for SPINAL.
       qHspnlm - Number of PULSES (not cycles!) in the .DEC file.
       ph1Hspnlm - TPPM +/- phase, "phi".
       ph2Hspnlm - additional SPINAL phase, "alfa".
       ofHspnlm - overall frequency offset.

The Basic SPINAL cycle Q is: [(phi),(-phi)],(phi+alfa),(-phi-alfa),(phi+2alpha),
                             (-phi-2alpha),(phi+alfa),(-phi-alpha). Note that
                             the first two elements [(phi),(-phi)] are TPPM.
SPINAL repeats with: [[Q-Q]-QQ]-QQQ-Q]. where the [] include 16,32 and 64 pulses.
                     The "Supercycle" of this SPINAL is one PULSE, (not Q).
Implementation: MPSEQ spnlm = getspnlm("spnlmH",0,0.0,0.0,0,1);
Underscore functions: _MPSEQ functions.

90X:  Module:  no
Sequence:  onepul.c
Description:  Provides a 90-degree pulse on obs that can be used as a
              preparation pulse. Also used to store the obs calibration.
Parameters:  Channels Page
      aX90  - the amplitude of the pulse.
      pwX90 - the pulse length.

180X:  Module:  no
Sequence:  twopul.c
Description:  Provides a 180-degree pulse on obs that can be used as an
              inversion or a refocussing pulse.
Parameters:  Sequence Page
      aX180 -  the amplitude of the pulse.
      pwX180 - the pulse length.

tconst = constant tau refocussing delay. 

