---------+---------+---------+---------+---------+---------+---------+---------+
========= DX-1 for E6392B User's Guide ========= 
Is a sample software running on a PC that provides flexible test and 
measurement sequence.

	Revision History (release date)
	Rev.A.01.00 Sep 29th 2000 
	Rev.A.01.01 Oct 25th 2000
	Rev.A.01.02 Nov 16th 2000	
	Origination		written by Hiroshi Takeda  
        	                Sep 19th 2000

Notification:
Customer shall have the personal, non-transferable rights to use, copy or modify 
the DX-1 software for Customer's internal operations. Customer shall use the DX-1
 Software solely and exclusively for its own purpose and shall not license, lease, 
market or distribute the DX-1 software or modification or any part thereof. 
Agilent Technologies shall not be liable for the quality, performance or behavior 
of the DX-1 software. Agilent Technologies especially disclaims that the operation 
of the DX-1 software shall be uninterrupted or error free.  This DX-1 software is 
provided AS IS.  AGILENT TECHNOLOGIES DISCLAIMS THE IMPLIED WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Agilent Technologies shall not be liable for any infringement of any patent, 
trademark, Copyright or other proprietary rights by the DX-1 or its use. 
Agilent Technologies does not warrant that the DX-1 software is free from 
infringements or such rights of third parties. However, Agilent Technologies will 
not knowingly infringe or deliver software that infringes the patent, trademark, 
copyright or other proprietary right of a third party.


	   (c) Copyright 2000, Agilent Technologies Co,
        	      All right reserved.

---------+---------+---------+---------+---------+---------+---------+---------+
 1. Introduction

This document describes the objectives, copyright, operation, and command reference 
of the software so-called �g DX-1�h.

1.1 Objectives of this software
  This software provides a flexible test sequence remote controlled from PC using 
  the E6392B GSM MS test set. 

1.2 Function overview
  The test sequence is defined in a text file that is called �gsequence file�h that 
  has a file extension of �g.seq�h. The sequence file needs to be generated in 
  advance by using any text editor and to be placed under the adequate directory on 
  the PC system. The commands available in the sequence file are defined at the end 
  of this document. All results will be write into the text file. 


---------+---------+---------+---------+---------+---------+---------+---------+
2. System Requirements
Here are the system configurations we recommend. We tested the software 
executioon only on the following system configuration.

2.1 Hardware Requirements
  - PC system hardware: A desktop PC or a note PC equipped with one serial port 
  - Instruments: Agilent E6392B GSM MS Test Set 
  - Cables: A serial cable for RS232 (cross)
 
2.2 PC System Requirements
 
  - For the desktop PC:
  - HP Kayak XA (Pentium CPU, Memory 98Mbyte)
  - Hard disk space: > 50 MByte
  - Operating system: Windows NT4.0
  - For the note PC:
  - HP Omnibook 800CT / 900 
  - Hard disk space: > 50 M Byte
  - Display: SVGA (800 x 600) or higher
  - Operating system: Windows 95/98

2.4 System Connection
Assumption: an operating system has already installed into the PC system.
  1) Connect all cables as shown in Fig 1.

---------+---------+---------+---------+---------+---------+---------+---------+
3. DX-1 Installation
Install the DX-1 software according to the following steps:

 You will find the files below after installation.
 
 Under the directory of C:\Program Files\DX-1
 DX-1.exe         : DX-1 program
 UsersGuide.doc   : User's Guide
 HowtoMakeSeq.txt : Guide for making Sequence File
 TestXXXXX.seq..  : Sequence Files
                       

 Note: If DX-1 is provided in floppy disks. Please create a new folder in your 
 hard disk drive and copy all contains of floppy into the folder. (If you execute 
 Setup.exe in floppy disk, it will take longer time to install DX-1 than the time 
 when you execute it in the hard disk.)


  1) Close all other applications on the PC.
  2) Point at the [Start] and [Run..] menu of the Windows, and select the 
  Setup.exe in the folder containing the file obtained from the Internet Web and 
  decompressed.  Click on [Browse..] as required, and search for the file. 
  In the case of a floppy disk, put the first disk in the drive, and select 
  the Setup.exe in the floppy disk according to the same procedure. 
  (To make setup floppy disks, see the next section 
  "If you would like to install from floppy disks".)
  3) Click on [OK], and the Setup Program will run.
  4) Follow the instructions indicated in the drawing.
  5) After completing the setup, point at the [Programs] of the [Start] menu, 
  and make sure that the Agilent E6392 group is registered.


---------+---------+---------+---------+---------+---------+---------+---------+