HP 6672A System Power Supply

This model is a 2000 Watt, single output, series pass regulated power supply, with an internal HP-IB interface and SCPI programming. This model provides many talker/listener functions including remote programming of voltage and current with feedback of actual measured output values. 16 supplies can be connected to one HP-IB interface via a serial link connection.

[ Features ]

Low ripple and noise
Fast up- and down-programming
SCPI (Standard Commands for Programmable instruments)
Complete front-panel control, calibration and display
Remote programming and sensing
Fan-speed control to minimize acoustic noise
Over-voltage and over-current protection
HP VXI plug&play drivers

[ Specifications ]

Output ratings (0 - 55 deg C): 0-20 V, 0-100 A
Programming Accuracy (at 25 deg C ± 5 deg C): 20 mV + 0.04%, 60 mA + 0.1%   
Ripple and noise (20 Hz to 20 MHz): CV: 750 uV rms, 9 mV peak-to-peak; 
                                    CC: 100 mA rms 
Readback accuracy: (at 25 deg C ± 5 deg C): 30 mV + 0.05%, 100 mA + 0.1% 
Line regulation: 650 uV + 0.002%, 7 mA + 0.005%
Load regulation: 650 uV + 0.002%, 7 mA + 0.005%  
Transient response time
Less than 900ms for the output voltage to recover 
100mV following a change in load from 100% to 50% or 50% to 100% 
of the output current rating of the supply.

Supplemental Characteristics
Average resolution
	Voltage:   5mV
	Current:  25 mA
	OVP:      35mV
Output Voltage programming response time*
	(excluding command processing time) System models only:  60 ms

*Full load programming rise/fall time (10% to 90% or 90% to 10%) 
with full resistive load equal to rated output voltage/rated output 
current.

Physical Specifications
	Size:  425.5 mm W x 132.6 mm H x 640 mm D 
               (16.75 in. x 5.22 in. X 25.2 in.)
	Weight:  Net, 28.2 kg (62 lb.); shipping, 31.8 kg (70 lb.)

[ Ordering ]

HP 6672A Single-output System Supply Opt 200 174 to 220 Vac, 47 to 63 Hz (Japan Only) Opt 908 Rack Mount Kit (HP p/n 5062-3977) Opt 909 Rack Mount Kit with handles (HP p/n 5062-3983) Opt 910 Service Manual and extra Operating Manual. Standard unit is shipped with operating manual only One of the following line cord options must be specified for the HP 667xA series. Opt 831 12 AWG wire size; unterminated line cord Opt 832 4 mm wire size; unterminated line cord Opt 834 10 AWG wire size; unterminatred line cord Opt 841 Line cord with NEMA 6-20P, 20A/250V plug Opt 842 Line cord with IEC 309, 32A/220V plug Opt 844 Line cord with NEMA L6-30P, 30A/250V locking plug

HP 1252-3698 7-pin Analog Plug HP 1252-1488 4-pin Digital Plug HP 5080-2148 Serial Link Cable 2m (6.6ft)

[ Key Literature ]

No literature is available online at this time.

[ Assistance ]

To help you make the right product choices

Customers outside the U.S. can obtain assistance through local HP DIRECT help.

[ Related ]

Related Information:

HP VXI plug&play drivers for HP 667xA Series System DC Power Supplies

Related HP 6670 Series System Power Supplies product datasheets:

HP 6671A System Power Supply

HP 6672A System Power Supply

HP 6673A System Power Supply

HP 6674A System Power Supply

HP 6675A System Power Supply

Related product families available online:

HP6670 Single Output 2,000W Series