HP 84110EM EMC Pre-production Evaluation System, 9 kHz to 1.8 GHz

The HP 84110EM has everything you need to perform radiated and conducted emissions measurements on your products and compare the results to agency limits. The system is based on the HP 8591EM EMC analyzer, which contains a quasi-peak adapter and dual I/O ports (HP-IB and parallel). The system also includes biconical and log periodic antennas, tripod, LISN, close field probe kit, limiter, and 10-meter cable.

[ Features ]

Automatic functions speed and simplify EMC evaluations and troubleshooting.
Complete measurement setups can be stored and recalled.
Test reports may be output directly to a printer.
Close field probes locate and isolate emission "hot spots."

[ Specifications ]

Frequency Specifications

Frequency Range 50 ohms: 9 kHz to 1.8 GHz Frequency Reference Aging: ±2 x 10⁶/year Temperature Stability: ±5 x 10⁶ Initial Achievable Accuracy: ±0.5 x 10⁶ Marker Count Accuracy Frequency Span <= 10 MHz x N* ±(marker frequency x frequence reference error¹ + counter resolution + 100 Hz x N*) Frequency Span >=10 MHz x N*: ±(marker frequency x frequency reference error¹ + counter resolution + 1 kHz x N*) Counter Resolution Frequency Span <=10 MHz x N*: Selectable from 10 Hz to 100 kHz Frequency Span >10 MHz x N*: Selectable from 100 Hz to 100 kHz Frequency Sweep Time Range Span = 0 Hz, > 1 kHz: 20 ms to 100 s Span = 0 Hz (Opt 101): 20 µ to 100 s Accuracy 20 ms to 100 s: ±=3% 20 µ to < 20 ms (Opt 101): ±=2% Sweep Trigger: Free run, single, line, video, external Resolution Bandwidth: 30 MHz to 3 MHz (3 dB) in 1-3-10 sequence 200 Hz, 9 kHz, and 120 kHz (6 dB) EMI bandwidths Accuracy: ±20% Selectivity (Characteristic) -60 dB/-3 dB 3 kHz to 10 kHz: 15:1 100 kHz to 3 MHz: 15:1 1 kHz, 30 kHz: 16:1 -40 dB/-3 dB 30 Hz to 300 Hz: 10:1 Video Bandwidth Range: 1 Hz to 1 MHz in 1, 3 sequence Stability Noise Sidebands (1 kHz RBW, 30 Hz VBW and sample detector) >10 kHz offset from CW signal <=-90 dBc/Hz + 20 Log N* >20 kHz offset from CW signal <=-100 dBc/Hz + 20 Log N* >30 kHz offset from CW signal <=-105 dBc/Hz + 20 Log N* Residual FM 1 kHz RBW, 1 kHz VBW <=250 Hz pk-pk in 100 ms 30 Hz RBW, 30 Hz VBW <=30 Hz pk-pk in 300 ms System-Related Sidebands >30 kHz offset from CW signal <=-65 dBc + 20Log N* *N = LO harmonic. N = 1. ¹ Frequency reference error = (aging rate x period of time since adjustment + initial achievable accuracy + temperature stability).

Amplitude Specifications

Amplitude Range  
                              Displayed average noise level to +30 dBm

Maximum Safe Input Level (Input attenuator >=10 dB)
   Average continuous power:  +30 dBm (1 W)
   Peak pulse power:	      +30 dBm (1 W)
   dc:			      25 Vdc

Gain Compression
   >10 MHz:		          <= 0.5 dB (total power at input mixer²= -10 dBm)
Displayed Average Noise Level 
(Input terminated, 0 dB attenuation, 1 Hz VBW, sample detector)
				30 Hz RBW		1 kHz RBW
   400 kHz to 1 MHz		<= -130 dBm		<= -115 dBm
   1 MHz to 1.5 GHz		<= -130 dBm		<= -115 dBm
   1.5 GHz to 1.8 GHz		<= -128 dBm		<= -113 dBm

Spurious Responses
Second Harmonic Distortion
   5 MHz to 1.8 GHz:          <-70 dBc for -45 dBm tome at input mixer²
Third Order Intermodulation
Distortion
   5 MHz to 1.8 GHz:	      <-70 dBc for two -30 dBm tones at input mixer² 
			      and >50 kHz separation.

Other Input Related Spurious
   <=1.8 GHz:	              <-65 dBc at >=30 kHz offset, for 
			      -20 dBm tone at input mixer²

Residual Responses (Input terminated and dB attenuation)
   150 kHz to 1.8 GHz:	      <-90 dBm

Frequency Response (10 dB input attenuation)
			Absolute³		Relative Flatness⁴
   9 kHz to 1.8 GHz:	±1.5 dB				±1.0 dB

²Mixer Power Level 9 (dBm) - Input Attenuation(dB)
³Referenced to 300 MHz CAL OUT
⁴Referenced to midpoint between highest and lowest frequency response deviations.



General Specifications

Temperature Range
   Operating:                 0 °C to +55 °C
   Storage:		  -40 °C to +75 °C

EMI Compatibility:            Conducted and radiated interference CISPR Pub. 11 and 
			      Messempfaenger Postverfuegung 526/527/79

Audible Noise:	              <37.5 dBa pressure and <5.0 Bels power (ISODP7779)

Power Requirements
ON (Line 1):	              86 to 127, or 195 to 250 V rms,
			      47 to 66 Hz, 103 to 126 V rms, 
			      400 Hz +/- 10% Power consumption 
			      <300 VA; <100W  
		
Standby (Line 0):	      Power consumption <7W

User Memory (nominal):        32 Kbytes non-volitile RAM

Data Storage (nominal):	      50 states and traces, internal 
			      memory and 8 internal state registers;
			      24 states and traces, memory card (HP 85700A)

[ Ordering ]

HP 84110EM Preproduction Evaluation System, 9 kHz to 1.8 GHz Opt 001 Replaces 11967D LISN with 11967D opt 001 LISN Opt 002 Replaces 11967D LISN with 11967D opt 002 LISN Opt 004 Adds precision frequency reference Opt 010 Adds the Tracking Generator Opt 015 Soft Tan Operating/Carrying Case Opt 016 Soft Yellow Operating/Carrying Case. Opt 043 Rpl HP-IB/parallel w/RS/parallel port Opt 093 Replaces HP 8591EM with HP 8593EM Opt 094 Replaces HP 8591EM with HP 8594EM Opt 095 Replaces HP 8591EM with HP 8595EM Opt 096 Replaces HP 8591EM with HP 8596EM Opt 193 Replaces HP 8591EM with HP 8593EM opt 010 Opt 194 Replaces HP 8591EM with HP 8594EM opt 010 Opt 195 Replaces HP 8591EM with HP 8595EM opt 010 Opt 196 Replaces HP 8591EM with HP 8596EM opt 010 Opt 61A Adds the HP 11961A Opt UK6 Commercial cal. certificate w/ test data Opt W30 3 Year Return Repair Service Opt W32 3 Year Calibration Customer Return Svc. Opt W34 3 Year Standards Compliant Cal Service Opt W50 5 Year Return Repair Service Opt W52 5 Year Cust Return Calibration Service Opt W54 5 Year Standards Compliant Cal Service

[ Key Literature ]

No literature is available online at this time.

[ Assistance ]
Additional help is a click away!

Want to talk to a knowledgeable engineer about this product at our HP Test and Measurement Call Center? Do you have a question you want to send in by e-mail? A measurement set-up you need to fax in? Follow the link above and you will be given a choice to contact an engineer by telephone, e-mail or fax.

This service is available only in the United States. For assistance outside the U.S., contact your local HP DIRECT or HP Sales Office.

[ Related ]

Related product families available online:

EMC Measurement Systems