![]() | ||||
![]() |
HP 85110A Pulsed RF S-Parameter Test Set, 2 GHz to 20 GHz![]()
|
General Specifications
Frequency Range: 2 to 20 GHz Test Ports (port 1 or 2) Nominal Operating Power Level: 0 to -3 dBm Connector Type: 3.5 mm, male Impedance, DC Bias: 50 ohm nominal, 500 mA, 40 Vdc maximum Attenuation Range (Incident Signal): 0 to 90 dB, in 10 dB steps RF Input Connector (Rear Panel): Maximum Input Power: +14 dBm Connector Type: 3.5 mm, female Dynamic Range1 (for transmission measurements, independent of duty cycle) Frequency Range (GHz) 2 to 8 8 to 18 18 to 20 Maximum Power (dBm) Measured at Port 22: +11 +11 +11 Reference Power (dBm) at Port 1 (nominal): +0 -1 -2 Minimum Power (dBm) Measured at Port 2 Pulsed: -64 -63 -62 CW: -78 -78 -77 Receiver Dynamic Range (dB) Pulsed: 75 74 73 CW: 89 89 88 System Dynamic Range (dB) Pulsed: 64 62 60 CW: 78 77 75 1Limited by compression level and system noise floor. Noise floor is measured with full two-port error correction, 1024 averages. 2This maximum power measurement assumes that the HP 85110A test set has its internal step attenuators set to 0 dB. The test can handle up to 20 W (+43 dBm) or power if the step attenuators are activated and an isolator is installed (in the port 2 real panel link).
Measurement Port Characteristics
Frequency Range (GHz) 2 to 8 8 to 18 18 to 20 Residual (dB) Directivity: 44 44 44 Source Match: 33 31 31 Load Match: 44 44 44 Reflection Tracking: ±0.003 ±0.006 ±0.006 Transmission Tracking: ±0.044 ±0.084 ±0.094 Crosstalk: 64 62 61
Pulsed-RF Detectors
Equivalent Measurement Bandwidth (-3 dB): 1.5 MHz Aperature Uncertainty: <1 nanosecond, typical Transition Time (10% to 90%): 300 nanoseconds Trigger Level: TTL (falling edge), external Trigger Width: 100 nanoseconds, minimum Minimum Time Display: 5 microseconds Maximum Time Display: 40 milliseconds
If you have Adobe's Acrobat Reader already available on your system, please click on the icon provided below to print or view the specifications.
If you do not have the Adobe Acrobat Reader necessary for viewing PDF documentation, download your free Acrobat Reader, and then click on the icon below.
HP 85110A Pulsed RF S-Parameter Test Set, 2 to 20 GHz Opt 001 Add IF switching circuitry Opt 908 Rack flange kit Opt 910 Additional operating and service manual Opt 913 Rack flange and handle kit Opt W32 3 Year Calibration Customer Return Service Opt W34 3 Year Standards Compliant Calibration Service Opt W52 5 Year Customer Return Calibration Service Opt W54 5 Year Standards Compliant Calibration Service
No literature is available online at this time.
Additional help is a click away!
Want to talk to a knowledgeable engineer about this product at our HP Test and Measurement Call Center? Do you have a question you want to send in by e-mail? A measurement set-up you need to fax in? Follow the link above and you will be given a choice to contact an engineer by telephone, e-mail or fax.
This service is available only in the United States. For assistance outside the U.S., contact your local HP DIRECT or HP Sales Office.
Related HP 8510C Network Analyzer Coaxial Test Sets Family product datasheets:
Related product families available online:
Page Updated: Thursday February 18 08:07:23 UTC 1999