|
| ||
|
|
HP 8571A Microwave EMI Receiver, 20 Hz to 22 GHz | |
![[ Summary ]](../Graphics/tab-summary.gif)
![[ Features ]](../Graphics/tab-features.gif)
![[ Specifications ]](../Graphics/tab-specs.gif)
![[ Ordering ]](../Graphics/tab-ordering.gif)
![[ Assistance ]](../Graphics/tab-assistance.gif)
The HP 8571A EMI receiver is capable of making your most demanding measurements over a wide (20 Hz to 22 GHz) frequency range. They are specifically designed to make essential military and commercial EMI measurements easily and quickly. The HP 8571A receiver includes an HP 8566B spectrum analyzer with Options 002 and 462, an HP 85685A RF preselector, an HP 11713A attenuator/switch driver, and an HP 8449B Option H02 preamplifier. This receiver is completely configured and verified by Hewlett-Packard and come with an individual calibration sheet to ensure ± 2 dB amplitude accuracy. They are shipped in a system cabinet. Owners of an HP 8566B can upgrade to an EMI compliance receiver by adding the spectrum analyzer options, accessory hardware, and factory calibration.
Frequency Specifications
(e1) Range: 20 Hz to 22 GHz Frequency Readout Resolution: 1 Hz Frequency Reference Error Aging: <2.5 x 10e-7/yr Temperature Drift: <7 x 10e-9 Frequency Accuracy Spans <= n x 5 MHz(e2): ± (2% of span + freq ref error x tuned freq + 0.3 x BW(sa) or 0.5 x BW(qp) + 10 Hz) Spans > n x 5 MHz: same as for spans <= n x 5 MHz, plus n x 100 kHz (e1)For instruments with Option 049 (delete µwave preamplifier and switch driver), the following specifications apply from 20 Hz to 2 GHz only. Above 2 GHz, standard HP 8566B specifications apply. (e2) where n = 1 for 20 Hz to 5.8 GHz center frequency n = 2 for 5.8 GHz to 12.5 GHz center frequency n = 3 for 12.5 GHz to 18.6 GHz center frequency n = 4 for 18.6 GHz to 22 GHz center frequency
Amplitude Specifications
Displayed Average Noise Level with 10 Hz resolution bandwidth(e3) 20 Hz: +35 dBµV 300 Hz: +23 dBµV 2 kHz: -5dBµV 9 kHz: -5 dBµV 9 kHz to 1 MHz: -25 dBµV 1 MHz to 1.5 GHz: -40 dBµV 1.5 to 2.0 GHz: -37 dBµV 2.0 to 5.8 GHz: -45 dBµV 5.8 to 12.5 GHz: -42 dBµV 12.5 to 18.6 GHz: -36 dBµV 18.6 to 22 GHz: -32 dBµV Maximum Safe Input Levels (Characteristic) DC Voltage Input 1: 0 Volts Input 2 or 3: ±20 Vdc Average Power Input 1 or 2: 30 dBm Input 3: 20 dBm Impulsive Signals Input 1: 2000 W peak for 10 µs pulse(e4) Input 2: 100 W peak for 10 µs pulse(e5) Measurement Range (Characteristic) Input 1 or 2: 137 dBµV to 3 dB above displayed average noise level Input 3: 70 dBµV to 3 dB above displayed average noise level (e3)0 dB HP 8566B attenuation and 0 dB HP 85685A attenuation. Characteristic displayed average noise level is 6 dB lower than specifications. (e4)>=20 dB HP 85685A attenuation. (e5)>=10 dB HP 8566B attenuation.
Spectral Purity
Absolute Amplitude Accuracy Input 1 or 2: < ± 2 dB 20 Hz to 2 GHz(e7) Input 3: < ± 2 dB 1 GHz to 22 GHz(e8) TOI (Characteristic) Input 1 or 2 Within RF Passband: 92 dBµV Outside RF Passband: 127 dBµV Input 3: 74 dBµV SOI (Characteristic) Input 1 or2 Within RF Passband: 127 dBµV Outside RF Passband: 147 dBµV Input 3: 97 dBµV 1 dB Gain Compression(e9) (Characteristic) Input 1 or 2 Within RF Passband: 77 dBµV Outside RF Passband: 117 dBµV Input 3: 70 dBµV IF Filters (in 1, 3, 10 sequence) 6 dB Bandwidths: 10 Hz to 300 Hz Impulse Bandwidths: 1 kHz to 3 MHz Detection Modes: Peak, Average Interference Rejection Image Responses (Characteristic): > 60 dB below signal, 20 Hz to 20 GHz > 50 dB below signal, 20 GHz to 22 GHz Spurious Responses (Characteristic): > 60 dB below signal power Residuals Inputs 1 and 2: < -5 dBµV, 9 kHz to 2 GHz Input 3: < 3 dBµV,1 GHz to 22 GHz (e7)10 dB HP 8566B attenuation, 0 to 20 dB HP 85685A attenuation and after system calibration procedure. With 0 dB HP 8566B attenuation, amplitude accuracy < ±2.5 dB. (e8)When calibration data is applied. (e9)0 dB HP 85685A attenuation and 0 dB HP 8566B attenuation.
Outputs and Inputs
Front Panel Outputs Calibrator: 100 MHz, 97 ±0.3 dBµV, 50 ohms Comb Generator: 0.1, 0.5, 1, or 5 MHz: 47 to 67 dBµV nominal Rear Panel Outputs Display: X, Y, Z, and Blanking outputs for external CRT Recorder: Sweep, video, and penlift outputs for X-Y recorder 21.4 IF: 87 dBµV for signal at reference level Frequency Reference: 10 MHz, 107 dBµV, 50 ohms External Audio: for use with an 8 ohm speaker Front Panel Inputs Input 1: 20 Hz to 50 MHz BNC (f) fused VSWR: < 1.5:1, >=10 dB input attenuation < 1.3:1 (Characteristic) < 2.2:1, 0 dB attenuation (Characteristic) Input 2: 20 MHz to 2 GHz Type N (f) VSWR: < 1.5, >=10 dB input attenuation < 1.2:1 (Characteristic) < 2.0:1, 0 dB attenuation (Characteristic) Inputs 1 and 2 LO Emissions: < -3 dBµV (Characteristic) Input Attenuators: 0 to 50 dB in 10 dB steps 3 dB linearity check attenuator Input 3 1 GHz to 22 GHz APC 3.5 (m) VSWR: < 2.0:1 (Characteristic) Input Filters (Characteristic): 16 automatically switched filters Start Frequency Stop Frequency Filter Type ------------------------------------------- 0 Hz 10 kHz LP, fixed 10 kHz 76 kHz BP, fixed 74 kHz 205 kHz BP, fixed 197 kHz 525 kHz BP, fixed 500 kHz 1 MHz BP, fixed 1 MHz 2 MHz BP, fixed 2 MHz 6 MHz BP, tuned 6 MHz 17 MHz BP, tuned 17 MHz 29 MHz BP, tuned 29 MHz 52 MHz BP, tuned 52 MHz 98 MHz BP, tuned 98 MHz 152 MHz BP, tuned 152 MHz 219 MHz BP, tuned 216 MHz 334 MHz BP, tuned 332 MHz 500 MHz BP, tuned 500 MHz 2 GHz BP, tuned Rear Panel Inputs External Trigger: 2.4 to 5 Volts into 1 k ohms External Frequency Reference: reference 10 MHz, 107 to 117 dBµV, 50 ohms Data Transfer Rate: 1001 point trace in 151 msec (characteristic)
General Specifications
Temperature Operating: 20 to 30°C Storage: -40 to 75°C EMI Compatibility: Meets MIL-STD-461C, 7(Air Force), Methods CE03 and RE02 Power Requirements: 50 to 60 Hz 100, 120, 220 or 240 volts (+5%, -10%), approximately 590 VA Direct Plotter Output: plots trace, graticule, and annotation Weight: 177 kg (390 lb) Dimensions: 1250 mm height 610 mm width 810 mm depth
HP 8571A EMI Receiver Opt 910 Add Set of Operation Manuals Opt 915 Add Set of Service Manuals Opt 8Z0 Delete System Rack Opt 049 Delete Microwave Preamplifier and Switch Driver Opt W30 3 year Customer Return Repair Coverage Opt W32 3 year Customer Return Calibration Coverage Opt E40 22 to 40 GHz Block DownconverterConducted EMC Accessories HP 11967A Current Probe 20 Hz to 2 MHz HP 11967B Current Probe 15 kHz to 50 MHz HP 11967C LISN 10 kHz to 105 MHz EMC Antennas and Accessories HP 11966A Magnetic Loop (115 V) 9 kHz to 30 MHz Opt 220 Magnetic Loop (220 V) HP 11966B Active Rod (115 V) 30 Hz to 50 MHz Opt 220 Active Rod (220 V) HP 11966C Biconical 30 MHz to 300 MHz HP 11966D Log Periodic 200 MHz to 1 GHz HP 11966E Double-Ridged Horn 1 MHz to 18 GHz HP 11966F Conical Spiral 200 MHz to 1 GHz HP 11966G Conical Spiral 1 GHz to 10 GHz HP 11966H Dipole Set 28 MHz to 1 GHz HP 11966I Double-Ridged Horn 200 MHz to 2 GHz HP 11966J Double-Ridged Horn 18 GHz to 40 GHz HP 11966K Magnetic Field Pick-up Coil 20 Hz to 50 kHz HP 11966L Coaxial Cable, 10m, N (m) connectors HP 11966M Coaxial Cable, 10m, BNC (m) connectors HP 11966N Log Periodic 200 MHz to 5 GHz EMC Positioning Accessories HP 11968B Manual Antenna Mast HP 11968C Antenna Tripod HP 11968E Manual Equipment Turntable Tracking Sources HP 85644A Tracking Source 300 kHz to 6.5 GHz HP 85645A Tracking Source 300 kHz to 26.5 GHz
To help you make the
right instrument choices
Page Updated: Thursday June 19 16:14:02 UTC 1997