Combat Arms 2869 Grove Way Castro Valley, California 94546-6709 Telephone (415) 538-6544 BBS = (415) 537-1777 REMOVING COPPER FOULING FROM RIFLE BARRELS As a copper jacketed bullet passes through a rifle barrel, it leaves a tiny trace of copper on the lands and grooves of the rifling within the barrel. The more the weapon is fired, the greater the amount of copper deposited within the barrel. The copper begins to fill the grooves and the accuracy of the rifle will drop off considerably. What you will initially notice is that the shot groups will begin to widen as well as start to stray from point of aim. The obvious cure for this problem is to simply remove the copper from the barrel! That's where the fun begins. The shooter typically uses Break-Free CLP, Hoppe's No. 9, Shooter's Choice or some less well known substance. Anyone who has ever seriously cleaned a barrel will know the labor involved in doing it correctly. The use of the bore brush rubbing against the inside of the barrel increases the likelihood that, sooner or later, the rod will ding the barrel and that will do nothing for accuracy. Worse yet, if you clean the barrel from the muzzle end and ding the barrel area within one inch of the muzzle, you can cause damage which will upset the correct bullet flight path (trajectory). Chemically removing the copper If we could safely chemically remove the copper, we would lessen the real chance of barrel damage. The problem then arises for a way to do the chemical removal without damaging the weapon. One of the best ways to remove copper from anything is to coat the copper with a solution contain- ing ammonia. In more concentrated forms it is called ammonium hydroxide. When copper comes into contact with ammonia, it begins to dissolve. To see an example of this phenomena, drop a simple one cent coin into a cup of household ammonia. It will take a bit of time to do it because the house- hold ammonia is a 9% solution and the variety sold by Combat Arms is a 28% solution. Our type is sometimes known as "aqua of ammonia." Preparing the copper removing cocktail To chemically remove the copper fouling, get an uncontaminated bottle of Hoppe's No. 9 and pour half of the bottle of Hoppe's No. 9 into another small sealable container. Now take our 28% solution of ammonium hydroxide (this is also called ammonium hydroxide rated at 26ø on the Baume' scale) and top off the bottle of Hoppe's No. 9 with this ammonium hydroxide. This gives you a copper removing cocktail made up of Hoppe's No. 9 and aqua ammonia in a 50-50 solution. The only thing even remotely critical here is to follow these steps. SAFETY INSTRUCTIONS 1. Always mix up your copper removing cocktail using a fresh and un- spoiled bottle of Hoppe's No. 9. It is easier to use this cleaning method when you use the wide mouth 4 ounce size of Hoppe's No. 9. So, spend some money on a new bottle of Hoppe's No. 9. 2. The fumes of this concentrated ammonium hydroxide can be a bit overpowering, so do not mix this solution in a closed room. MIX THIS SOLUTION UP OUTSIDE WHERE THERE IS PLENTY OF VENTILATION! Concentrated ammonium hydroxide will really clean out your sinuses. 3. If you spill any of the ammonium hydroxide on your skin, you should wash it off immediately in clear, cold running water to avoid any possible sensitivity and irritation. Applying the solution To clean the barrel now becomes a simple job. Just position the weapon muzzle down in a plastic bucket that has some rags in the bottom of the bucket. The purpose of having the rags underneath the muzzle is to catch or collect all of the contaminants and fluid coming out of the barrel. The reason behind the bucket is to prevent the rags from contaminating the flooring the bucket is on. For Pete's sake, don't be so stupid as to try this over your wife's new carpet because you will be moon bound if you do! Now take an eyedropper and carefully fill it with the cocktail. Then drop the cocktail into the chamber end of the barrel with the eyedropper. Rotate the barrel to get the cocktail over all of the internal surfaces of the barrel. Once the inside of the barrel is sufficiently covered with the cocktail, it is necessary to give the solution some time to dissolve the copper. So, go eat breakfast/lunch/dinner, mow the grass or something for 15-20 minutes while the chemistry does its magic. While you are doing something else, your barrel is really cleaning itself! The finishing touches Once the ammonium hydroxide has had a chance to work on the copper, you then need to swab out the barrel and put a coat of Break-Free CLP or other gun oil on the inside and outside of the barrel. The barrel is now copper free! Because of the mess this makes (the rags that were under the muzzle will have a blue-green tint to them indicating the copper is coming out of the barrel), Combat Arms recommends that you clean all of the other parts of the gun before you treat the barrel. If you will treat the barrel with this method after about 250 to 500 rounds, you will be much more satisfied with your weapon's accuracy. Something that some of our shooters do is to carry a bottle containing the cocktail with them to the range. Then, during a lull in the shooting, they simply put a patch on a cleaning rod, dip it into the cocktail and run the patch down the barrel. This is then followed by a series of dry patches until the bore is completely dry. The gun is now ready to fire again. This procedure is used to keep the copper from building up and reduces the need to strip all of the copper out as previously outlined.