PC87363  Product Folder

The PC87363, a member of National SemiconductorÆs 128-pin LPC SuperI/O family, introduces a Musical Instrument Digital Interface (MIDI) Port and Game Port inputs for up to two game devices. It also offers wake-up support for a wide range of wake-up events and new hardware and software features to protect the system design. Like all members of this family, it is PC99 and ACPI compliant and offers a single-chip solution to the most commonly used PC I/O peripherals.

The PC87363 also incorporates: Fan Speed Control and Monitoring for two fans, a Floppy Disk Controller (FDC), a Keyboard and Mouse Controller (KBC), ACCESS.bus® Interface (ACB), System Wake-Up Control (SWC), General-Purpose Input/Output (GPIO) support for a total of 49 ports and an enhanced WATCHDOG Timer, a full IEEE 1284 Parallel Port and two enhanced Serial Ports (UARTs), one with Infrared (IR) support.

Outstanding Features

• MIDI Port compatible wi th MPU-401 UART mode
• Game Port inputs for up to two game devices
• Extended Wake-Up support, including legacy/ACPI power button support, direct power supply control in response to wake-up events, power-fail recovery
• Protection features, including chassis intrusion detection, GPIO lock and pin configuration lock
• Serial IRQ support (15 options)
• Bus interface, based on IntelÆs LPC Interface Specification Revision 1.0, September 29th, 1997
• Fan Speed Control and Monitor for two fans
• ACCESS.bus Interface, SMBus® physical layer compatible
• 49 GPIO Ports (37 standard, including 23 with Assert IRQ/#SMI/#PWUREQs interrupts; 12 V_SB powered)
• Blinking LEDs
• 128-pin PQFP Package

• Musical Instrument Digital Interface (MIDI) Port
• Compatible with MPU-401 UART mode
• 16-byte Receive and Transmit FIFOs
• Loopback mode support

• Game Port (GMP)
• Compatible with the Legacy Game Port definition
• Full digital implementation
• Supports up to two analog game devices

• Extended Wake-Up
• Legacy and ACPI power button support
• Direct power supply control in response to wake-up events
• Power-fail recovery

• Protection
• Chassis intrusion detection (CHASI, #CHASO)
• GPIO lock
• Pin configuration lock

• Fan Speed Control and Fan Speed Monitor (FSCM)
• Supports different fan types
• Speed monitoring for two fans
• Digital filtering of the tachometer input signal
• Alarm for fan slower than programmable threshold speed
• Alarm for fan stop
• Two speed control lines with Pulse Width Modulation (PWM)
• Output signal in the range of 6 Hz to 93.75 KHz
• Duty cycle resolution of 1/256

• 49 General-Purpose I/O (GPIO) Ports
• 37 standard, with Assert IRQ/#SMI/#PWUREQfor 23 ports
• 12 V_SB powered
• Programmable drive type for each output pin (open-drain, push-pull or output disable)
• Programmable option for internal pull-up resistor on each input pin
• Output lock option
• Input debounce mechanism

• LPC System Interface
• Synchronous cycles, up to 33 MHz bus clock
• 8-bit I/O cycles
• Up to four DMA channels
• 8-bit DMA cycles
• Basic read, write and DMA bus cycles are 13 clock cycles long

• PC99 and ACPI Compliant
• PnP Configuration Register structure
• Flexible resource allocation for all logical devices
• Relocatable base address
• 15 IRQ routing options
• Four optional 8-bit DMA channels (where applicable)

• Floppy Disk Controller (FDC)
• Programmable write protect
• FM and MFM mode support
• Enhanced mode command for three-mode Floppy Disk Drive (FDD) support
• Perpendicular recording drive support for 2.88 MB
• Burst and non-burst modes
• Full support for IBM Tape Drive register (TDR) implementation of AT and PS/2 drive types
• 16-byte FIFO
• Software compatible with the PC8477, which contains a superset of the FDC functions in the microDP8473, the NEC microPD765A and the N82077
• High-performance, digital separator
• Standard 5.25" and 3.5" FDD support

• Parallel Port
• Software or hardware control
• Enhanced Parallel Port (EPP) compatible with new version EPP 1.9 and IEEE 1284 compliant
• EPP support for version EPP 1.7 of the Xircom specification
• EPP support as mode 4 of the Extended Capabilities Port (ECP)
• IEEE 1284-compliant ECP, including level 2
• Selection of internal pull-up or pull-down resistor for Paper End (PE) pin
• PCI bus utilization reduction by supporting a demand DMA mode mechanism and a DMA fairness mechanism
• Protection circuit that prevents damage to the parallel port when a printer connected to it powers up or is operated at high voltages, even if the device is in power-down
• Output buffers that can sink and source 14 mA

• Serial Port 1 (SP1)
• Software compatible with the 16550A and the 16450
• Shadow register support for write-only bit monitoring
• UART data rates up to 1.5 Mbaud

• Serial Port 2 with Infrared (SP2)
• Software compatible with the 16550A and the 16450
• Shadow register support for write-only bit monitoring
• UART data rates up to 1.5 Mbaud
• HP-SIR
• ASK-IR option of SHARP-IR
• DASK-IR option of SHARP-IR
• Consumer Remote Control supports RC-5, RC-6, NEC, RCA and RECS 80
• Non-standard DMA support - one or two channels
• PnP dongle support

• Keyboard and Mouse Controller (KBC)
• 8-bit microcontroller
• Software compatible with the 8042AH and PC87911 microcontrollers
• 2 KB custom-designed program ROM
• 256 bytes RAM for data
• Five programmable dedicated open-drain I/O lines
• Two data registers and one status register during normal operation
• Support for both interrupt and polling
• 93 instructions
• 8-bit timer/counter
• Support for binary and BCD arithmetic
• Operation at 8 MHz,12 MHz or 16 MHz (programmable option)
• Can be customized by using the PC87323, which includes a RAM-based KBC as a development platform for KBC code

• ACCESS.bus Interface (ACB)
• Serial interface compatible with physical layer
• Compatible with PhilipsÆ I²C®
• ACB master and slave
• Supports polling and interrupt controlled operation
• Optional internal pull-up on SDA and SCL pins

• WATCHDOG Timer
• Times out the system based on user-programmable time-out period
• System power-down capability for power saving
• User-defined trigger events to restart WATCHDOG
• Optional routing of WATCHDOG output on IRQ and/or SMI lines

• System Wake-Up Control (SWC)
• Power-up request upon detection of Keyboard, Mouse, #RI1, #RI2, #RING activity and General-Purpose Input Events, as follows:
• Preprogrammed Keyboard or Mouse sequence
• External modem ring on serial port
• Ring pulse or pulse train on the #RING input signal
• Preprogrammed CEIR address in a preselected standard (NEC, RCA or RC-5)
• General-Purpose Input Events
• IRQs of internal logical devices
• Optional routing of power-up request on IRQ, #SMI and/or #PWBTOUT
• Battery-backed event configuration
• Programmable V_SB-powered output for blinking LEDs (LED1, LED2) control

• Clock Sources
• 48 MHz clock input
• LPC clock, up to 33 MHz
• On-chip low-frequency clock generator for wake-up

• Power Supplies
• 3.3V supply operation
• Main (V_DD )
• Standby (V_SB)
• Battery backup (V_BAT)
• All pins are 5V tolerant and back-drive protected, except LPC bus pins

• Strap Configuration
• Base Address (BADDR) strap to determine the base address of the Index-Data register pair
• Test strap to force the device into test mode (reserved for National Semiconductor use)
• Power Supply and LED Configuration (PSLDC0,1) straps to determine the power supply control functions and the V_SB power-up defaults of LED2
• Power Supply On Polarity (PSONPOL) strap to set PSON active state and output type

National Semiconductor is a registered trademark of National Semiconductor Corporation.
All other brand or product names are trademarks or registered trademarks of their respective holders.